Search found 94 matches

by petergebruers
20 Oct 2017 12:35
Forum: Z-Uno
Topic: New 2.1.1 release!
Replies: 2
Views: 91

Re: New 2.1.1 release!

I am not sure. I was running Arduino 1.8.4 during beta tessting but now I am running the release version on Arduino1.8.5. Do you have stuff that does not run on 1.8.5?
by petergebruers
19 Oct 2017 17:13
Forum: Z-Uno
Topic: Enable Hardware Watchdog
Replies: 11
Views: 51

Re: Enable Hardware Watchdog

Forgot something important... there is an issue with that version on windows, if your user directory has a space in its path...
by petergebruers
19 Oct 2017 17:11
Forum: Z-Uno
Topic: Enable Hardware Watchdog
Replies: 11
Views: 51

Re: Enable Hardware Watchdog

@apica, have you tried 2.1.1 yet? I can recommend it, it contains a lot of improvements. And if it does not, I offer you a helping hand, ... Please let me know what you think...
by petergebruers
17 Oct 2017 12:31
Forum: Z-Uno
Topic: Mobile Z-Uno and connection loss
Replies: 7
Views: 102

Re: Mobile Z-Uno and connection loss

I have to say... I live in a small house... it won't be a good test. I have a small garden and I only have one "weak spot", meaning a place that does not have a direct connection to my controller. So it is not a good test, my device will find out the additional route in the garden and that's it. Sor...
by petergebruers
17 Oct 2017 12:23
Forum: Z-Uno
Topic: Z-Uno battery powered at 18V
Replies: 12
Views: 130

Re: Z-Uno battery powered at 18V

The battery pin and the 3.3 V pin are the same. That is where you connect your 3.3 V supply. No voltage will appear on the 5 V or the V ext pins. One thing you might want to consider is this: what happens if you connect USB (to flash, to experiment) and your external 3.3 V at the same time, but your...
by petergebruers
17 Oct 2017 11:38
Forum: Z-Uno
Topic: Z-Uno battery powered at 18V
Replies: 12
Views: 130

Re: Z-Uno battery powered at 18V

Yes, everything on your Z-Uno gets power from the 3 V pin.
by petergebruers
17 Oct 2017 11:33
Forum: Z-Uno
Topic: Send multiple values at once
Replies: 10
Views: 120

Re: Send multiple values at once

In Indigo, when changing associations, do you see a distinction between "single channel" and "multi channel"? PoltoS wants you to check if your controller "1" was listed under "single". If it was, please remove it and add it under "multi". On Fibaro, you see two colums, one marked S and one marked M.
by petergebruers
16 Oct 2017 15:27
Forum: Z-Uno
Topic: Z-Uno battery powered at 18V
Replies: 12
Views: 130

Re: Z-Uno battery powered at 18V

I have checked it, it is OK to supply power to the 5 V pin, the 5 -> 3 V regulator only adds 12 uA on my board at room temperature. No need to remove R12, it is not there to "squeeze out some uA". By removing R12 you disconnect the 3 V regulator from the 3 V pin and the battery. So it no longer can ...
by petergebruers
16 Oct 2017 10:45
Forum: Z-Uno
Topic: Mobile Z-Uno and connection loss
Replies: 7
Views: 102

Re: Mobile Z-Uno and connection loss

I moved my Z-Uno to a spot with no direct connection to the controller... It did not cause any issues with my network. The test is not very scientific. I can do a better test, if you want me to do that, but it takes some time and a really careful setup... I can activate my Z-Sniffer and check if the...
by petergebruers
15 Oct 2017 23:17
Forum: Z-Uno
Topic: Send multiple values at once
Replies: 10
Views: 120

Re: Send multiple values at once

I ran a test sketch based on your info (code below) on my Z-Uno 2.1.1 and Z-Way controller and it works as expected. Both light levels (one single channel and one multi channel) update every 10 s. All three wind values (one single channel and 2 multi channel) update at the same time every 30 s. Also...