Search found 12 matches
- 28 Oct 2023 12:54
- Forum: Device specific
- Topic: FGWPG-111 Parameter settings
- Replies: 1
- Views: 9912
Re: FGWPG-111 Parameter settings
May have answered my own question. Via the "_Expert commands option"
- 28 Oct 2023 12:08
- Forum: Device specific
- Topic: FGWPG-111 Parameter settings
- Replies: 1
- Views: 9912
FGWPG-111 Parameter settings
How do I change parameters such as:
1.power change in percent
2.Energy reporting threshold
3.Periodic power reporting
4.Periodic energy reporting
Via the UI?
1.power change in percent
2.Energy reporting threshold
3.Periodic power reporting
4.Periodic energy reporting
Via the UI?
- 29 Jul 2023 15:03
- Forum: Official announcements
- Topic: job queue runs full after upgrade to v4.1.0
- Replies: 126
- Views: 185919
Re: job queue runs full after upgrade to v4.1.0
Just to be clear - I managed to update to 7.38 but doesn't fix the Z-Wave chip firmware issue (SiLabs SDK)
- 28 Jul 2023 19:46
- Forum: Official announcements
- Topic: job queue runs full after upgrade to v4.1.0
- Replies: 126
- Views: 185919
Re: job queue runs full after upgrade to v4.1.0
My firmware is 7.36. The UI says "Your stick uses the latest firmware". You say "You need to upgrade your firmware to the latest" but it seems it already is ????
- 27 Jul 2023 16:55
- Forum: Official announcements
- Topic: job queue runs full after upgrade to v4.1.0
- Replies: 126
- Views: 185919
Re: job queue runs full after upgrade to v4.1.0
I spoke too soon.
When operating any switch Node I get 3 x Not delivered + Removing jot due to too many retransmissions. Then "check if node has failed" + Node is operating. Restarting the service does not fix but power cycle does- 27 Jul 2023 10:19
- Forum: Official announcements
- Topic: job queue runs full after upgrade to v4.1.0
- Replies: 126
- Views: 185919
Re: job queue runs full after upgrade to v4.1.0
v4.1.1 locked on me again after about 6 hours so rolled I back to the earlier beta which was faultless for me over several days
- 17 Jul 2023 22:58
- Forum: RaZberry
- Topic: jobs stuck in queue
- Replies: 5
- Views: 13171
Re: jobs stuck in queue
I installed the beta version and so far no reoccurrences of the problem.
- 16 Jul 2023 23:59
- Forum: RaZberry
- Topic: jobs stuck in queue
- Replies: 5
- Views: 13171
Re: jobs stuck in queue
Have you had any success in resolving it? As I see it there could be a somewhat faulty node but is should never cause the item to get stuck, after all that is what the timeout is there for.
- 16 Jul 2023 16:31
- Forum: RaZberry
- Topic: jobs stuck in queue
- Replies: 5
- Views: 13171
jobs stuck in queue
I have upgraded my several years old Smart Home controller to the latest Pi4 + Z-Wave.Me RaZberry 7 Pro (with external Antenna) + latest firmware after experiencing some strange problems with jobs stuck in queue. To my surprise the problem persists. Everything runs OK for a couple of hours or so the...
- 13 Jun 2023 19:20
- Forum: RaZberry
- Topic: Loss of interview
- Replies: 0
- Views: 36102
Loss of interview
My Z-Wave.me Pi with pigyback Z-Wave serial board has around 25 nodes and has been running quite well for several years aside from Pi SD card failures from time to time. Every now and again I may add another node but mostly things stay constant. Over the last several months, every week or two severa...