Search found 22 matches
- 31 Jan 2019 12:09
- Forum: Z-Uno
- Topic: Validation check for config parameters
- Replies: 2
- Views: 2945
Re: Validation check for config parameters
I suggest to always validate the paramters read using zunoLoadCfgParam and use a fallback. The fallback could be to overwrite the values with a correct default. And it should be no problem to overwrite using zunoSaveCfgParam in your handler! But i'm on your side, it would be better if, for example, ...
- 31 Jan 2019 11:50
- Forum: Z-Uno
- Topic: Battery Values
- Replies: 1
- Views: 2305
Battery Values
Hi! i use a CR123a battery to power an Z-Uno with Z_UNO_SLEEPINGMODE of SLEEPING. The battery value that is reported by the Z-Uno seems to be way to low. I changed the battery to a totaly new one and the reported value is 68%. The battery voltage is 2.98v (measured with a voltmeter). I would expect ...
- 02 Nov 2018 13:29
- Forum: Z-Uno
- Topic: Change Logging Settings with 2.1.4
- Replies: 1
- Views: 2563
Change Logging Settings with 2.1.4
Hi, i enabled logging to UART0 and get some SFxx Information. But now I want to disable the Logging, but I cannot, the logging is there even after new upload of a sketch. I tried to burn the bootloader again, but the only thing I get is a message that the boot loader is already the installed require...
- 29 Oct 2018 11:54
- Forum: Z-Uno
- Topic: Wakeup not working at all
- Replies: 14
- Views: 14734
Re: Wakeup not working at all
I can confirm this and have the same problem with a sketch using ZUNO_SLEEPING_MODE_SLEEPING and zunoSendDeviceToSleep(). I set the wakeup to 4min... the z-uno wakes and is sending its reports. But it does not receive any waiting configuration messages from the controller. I guess it does not send a...
- 28 Oct 2018 00:20
- Forum: Z-Uno
- Topic: Battery Power and UART0
- Replies: 3
- Views: 3375
Re: Battery Power and UART0
Thanks for your reply.
You mean i should try a power only usb cable? But if i use usb everything is fine... problem starts if i use a battery and no usb at all.
You mean i should try a power only usb cable? But if i use usb everything is fine... problem starts if i use a battery and no usb at all.
- 27 Oct 2018 22:00
- Forum: Z-Uno
- Topic: Battery Power and UART0
- Replies: 3
- Views: 3375
Battery Power and UART0
Hi,
If i power using a 3,3v battery the Serial0 prints only garbadge. If i using USB Power the same Sketch works perfectly and i see the UART0 output. Do this have todo with the 3.3v power?
Bye
Nino
If i power using a 3,3v battery the Serial0 prints only garbadge. If i using USB Power the same Sketch works perfectly and i see the UART0 output. Do this have todo with the 3.3v power?
Bye
Nino
- 15 Mar 2018 11:18
- Forum: Z-Uno
- Topic: Remove original-antenna with ufl connector soldered?
- Replies: 1
- Views: 2420
Remove original-antenna with ufl connector soldered?
Hello,
just a short question. Do i always need to remove the original antenna if i solder a ufl connector and leave it unconnected or can i use the original antenna anyway?
Thx and Bye
just a short question. Do i always need to remove the original antenna if i solder a ufl connector and leave it unconnected or can i use the original antenna anyway?
Thx and Bye
- 12 Dec 2017 17:56
- Forum: Z-Uno
- Topic: Multilevel Sensor: Channel #0 not updated to value of channel #1
- Replies: 4
- Views: 5169
Re: Multilevel Sensor: Channel #0 not updated to value of channel #1
Thanks for your reply! Do you mean i should use ZUNO_SETUP_ASSOCIATIONS macro?
- 10 Dec 2017 19:30
- Forum: Z-Uno
- Topic: Config Parameters are note set/received
- Replies: 8
- Views: 8929
Re: Config Parameters are note set/received
Does someone have a working example of user channels?
- 10 Dec 2017 19:30
- Forum: Z-Uno
- Topic: Multilevel Sensor: Channel #0 not updated to value of channel #1
- Replies: 4
- Views: 5169