Updating Razberry

[Topas]

I just tried to run an update with the expertui - now my system seems to be broken.

It displays : "The current firmware version is: 5.04 [Bootloader: 48059]"
But commands to my devices fail since I ran the automatic update.
Could you help me which bootloader-files und firmware files I have to upload to get the system alive again?

[Topas]

Serial updater shows:

SERIAL INFO
VERSION: 05 04 VENDOR: 01 47

ZME_CAPABILITIES
UID: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
VENDOR: 00 00 NODES: 00
FLAGS: 00 00 00 00 00 00 00 00 00 00 00 00 00

FIRMWARE CRC
BOOT: BB BB FW: 52 62
MISC
FREQ: EU

NVR Content
--------------------------------------------------------------------------------------------
Prog/erase lock : FF FF FF FF FF FF FF FF, Read back lock: FF
Rev 01, Cal 03, TXCal 16 11, SAW 0D 3C DE 05, Pin 01, CRC C9 B8
NMV: CS 04, TYPE 02, SIZE 01 00, PSIZE 01 00 (EEPROM M25PE20)
USB: VID 00 01, PID 00 02, UUID 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
--------------------------------------------------------------------------------------------
FACTORY ID: WEEK 33, YEAR 17, CHIP 06 A9, SER 03 69, WS 82, HWREV: 00 01, CRC8 59

elapsed 5.32253503799 seconds

[Topas]

Now I managed to run some updates via ssh. And get the following output:

Code: Select all

 Z-WAVE Serial API Tool
                                             Version:LWE0.9
                                             by Z-WAVE>ME


-->
Device ready in:3.06252789497 seconds
          FULL INFO
Openning port                            ..............................                            OK


          SERIAL INFO
                 VERSION:  05 17  VENDOR:  01 47

          ZME_CAPABILITIES
                     UID:  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
                  VENDOR:  00 00   NODES: 00
                   FLAGS:  00 00 00 00 00 00 00 00 00 00 00 00 00

          FIRMWARE CRC
                    BOOT:  FF FF      FW:  FF FF
          MISC
                    FREQ:  EU

                                         NVR Content
          --------------------------------------------------------------------------------------------
          Prog/erase lock :  FF FF FF FF FF FF FF FF, Read back lock: FF
          Rev FF, Cal FF, TXCal  FF FF, SAW  FF FF FF FF, Pin FF, CRC  FF FF
          NMV: CS FF, TYPE FF, SIZE  FF FF, PSIZE  FF FF (EEPROM Unknown)
          USB: VID  FF FF, PID  FF FF, UUID  FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          --------------------------------------------------------------------------------------------
          FACTORY ID: WEEK 255, YEAR 255, CHIP  FF FF, SER  FF FF, WS 255, HWREV: FF FF, CRC8 FF

          elapsed 5.35259699821 seconds

But I still can´t communicate with my devices : "Could not be delivered to Z-Wave stack"

[Topas]

Now I managed to Update to the latest firmware 5.39 - I just started again on the terminal and the used the UI.

So this is solved.

[bottomhuddle]

My operating system is Windows 10 64-bit. The CP2102 USB drivers from silabs.com have been installed.
Arduino has just been reinstalled, and the computer has been reset. Uninstalling/reinstalling the USB driver Rescue mode and factory reset attempts made.